Safety Info Posts

EPA explains the difference between a PHA and a “Hazard Review”

For those who fall under EPA’s RMP rule, you are familiar with the three (3) program levels your process(s) will fall under and each of these program levels has varying degrees of hazard recognition requirements.  Many professionals involved in process safety are familiar with the term Process Hazards Analysis (PHA), but an RMP Program 2…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

NFPA Partners with United States Fire Administration to Promote Winter Fire Safety

The National Fire Protection Association (NFPA), in conjunction with the Federal Emergency Management Agency (FEMA)’s United States Fire Administration (USFA), has announced a new public safety campaign targeting winter fires. The Put a Freeze on Winter Fires campaign is intended to boost public awareness of common winter fire risks and to provide guidance and approaches…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

W.L. Gore & Associates Issue Safety Alert for Gore Moisture Barriers

The IAFF Division of Occupational Health, Safety and Medicine has been notified of a safety issue concerning stored fire fighter turnout gear. W.L. Gore & Associates has issued a safety alert for all users of Gore moisture barriers. The identified problem involves seam tape separation when the gear has been stored in its original packaging…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

OSHA cites concrete company for 10 violations after worker fatally engulfed in fly-ash silo

A concrete company has been cited for ten serious safety violations by OSHA after a plant operator, 39, was fatally engulfed in a fly-ash storage silo on Aug. 6. The worker entered the cone-bottom silo in an attempt to break up clumps of fly ash that had clogged the bottom discharge. After attempts to dislodge…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

PHMSA answers the question… Who regualtes the unloading of ammonia to a process

This response to your letter regarding training requirements under the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to a truck driver who is responsible for loading and unloading hazardous materials from a cargo tank motor vehicle with the power unit attached. Specifically, you are unclear on whether the Occupational Safety and Health Administration…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

First (1st) Public Review of Standard BSR/IIAR 2-201x, Safety Standard for Equipment, Design, and Installation of Closed-Circuit Ammonia Mechanical Refrigeration Systems (11/22/13 – 1/6/14)

A first (1st) public review of draft standard BSR/IIAR 2-201x, Safety Standard for Equipment, Design, and Installation of Closed-Circuit Ammonia Mechanical Refrigeration Systems is now open. The International Institute of Ammonia Refrigeration (IIAR) invites you to make comments on the draft standard. Substantive changes resulting from this public review will also be provided for comment in a…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

AMAZING video on studies looking at INCENTIVES and what REALLY MOTIVATES US!

RSA Animate – Drive: The surprising truth about what motivates us Of course I am posting this with the slant to “safety incentives”, but this video DESTROYS the concept of incentives with the review of some very valid and significant studies.  THIS IS A MUST SEE for anyone that already has or is considering starting…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here

2013 Video of the Week #47 (Pressure Vessel Hydro Failure)

This week’s video is meant to keep our focus on pressure vessel management.  Although this video is on a MUCH smaller scale than what an industrial plant would deal with, it does show us how a pressure vessel is hydro’ed (pressure tested), how the vessel can fail, how critical it is to uses “coded/certified” welders,…...

Membership Required

You must be a member to access this content.

View Membership Levels

Already a member? Log in here
Scroll to Top